Smogtips
CHOOSE YOUR CITY OR ZIPCODE:
Within:
SELECT SMOG CHECK TYPE:  

Join the community and post your question. Use our Ask-A-Tech for free now! ASE experts standing by.

Forum > General Smog Check > Question

How Do I Drive a Honda Fit to Set the Emissions Computer?

I don't know what it is called but the test item on the smog check for my Honda Fit 2010 needs to be set by driving a certain way. Certain speeds at certain times. I think the smog tech mentioned a Drive Cycle? What do I do?
Answer:

It appears your Honda Fit failed the smog inspection because its emission monitors were not ready. Monitors are internal self tests which the engine computer performs to ensure all emission systems are functioning properly. Typically driving for a few hundred miles over the course of a week, in both highway and city conditions, is enough to set the emission monitors. Usually the required drive cycle parameters are met over the course of 200-300 miles. However, due to different driving habits, the criteria required to run a monitor may not always be met; and a Honda Fit drive cycle must be performed. By following the Honda Fit drive cycle below all emission monitors will run. The Honda Fit drive cycle must be followed accurately. Take extra caution when performing the drive cycle on public roadways. Perform the drive cycle at your own risk. If you feel you might not be able to perform the drive cycle safely, or obey all traffic laws, seek the assistance of a smog check repair station or Honda Service Center.

How to Complete Honda Fit Drive Cycle

A. COLD START: Begin from Cold Start, and ignition in OFF position for at least 1 hour. Ensure your Honda Fit's fuel tank is between 1/4 and 3/4 full and engine coolant temperature is below 122°F and within 11°F of the ambient air temperature. Do not leave the key on prior to the cold start.

B. IDLE TIME: Start the engine (do not drive) and allow to idle for 2 1/2 minutes with the air conditioner on and rear defroster on. During this period the ECU will be running the Oxygen Sensor Heater self-test, Air Injection System Passive Air test, EVAP Purge "No Flow" test, Misfire Detection.

C. DRIVE: Turn off the air conditioner and rear defroster and begin driving. When possible, speed up to 55 mph. The ECU will now run self-tests on the Misfire Detection, Fuel Trim, and EVAP Purge Flow.

D. HOLD STEADY: Keep vehicle speed steady at 55 mph for three (3) minutes. During this time the Oxygen Sensor O2 response, Air Intrusive (AIS System), EGR Flow, Purge Valve, Misfire Detection, and Fuel Trim diagnostics will be performed.

E. DECELERATE: Slowly let off the accelerator pedal. Do not brake or shift in order to slow down. It is important to let your Fit coast gradually, slowing down to 20 mph. The ECU will once again self-test the EGR System, EVAP Purge System and Long Term Fuel Trims.

F. ACCELERATE: Accelerate, using 3/4 throttle, until 55-60 mph is reached. This will perform the same self tests as during the first acceleration step C.

G. HOLD STEADY: Hold steady speed once again. This time at 55mph for five minutes. During this time, in addition to running the self-tests as during the first HOLD STEADY step, the ECU will perform the catalyst monitor diagnostics. If the catalyst (Catalytic Converter) is marginal or the battery has been disconnected, it may take 5 complete driving cycles to determine the state of the catalyst,or in order to Complete the CAT Monitor.

H. DECELERATE: This will perform the same diagnostics as in Step E. Remember not to depress the brakes or shift gears during deceleration.

This should complete the drive cycle on your Honda Fit. To ensure all monitors are complete use a scan tool. We recommend completing this drive cycle twice in case in any step timing or speed was not achieved.


posted by SmogTips Support

 

View SmogTips.com in: Desktop / Mobile