Smogtips
CHOOSE YOUR CITY OR ZIPCODE:
Within:
SELECT SMOG CHECK TYPE:  

Join the community and post your question. Use our Ask-A-Tech for free now! ASE experts standing by.

Forum > General Smog Check > Question

Driving Cycle 2000 Mercedes Benz C230 Kompressor

Hi there, I am having a hard time getting my OBDII ready due to driving cycle. There are too many cycles on the Web, which one do I need to use to get my monitors to set? Also can this be reffered to a referee for smog inspection? Thanks for the help.
Answer:

We recommend using the drive cycle below. A note regarding engine cold starts... an engine cold start means the engine is started when the engine coolant temperature is below 122°F and within 11°F of the ambient air temperature. The drive cycle requires the engine be started when cold, i.e. cold start. Follow the Mercedes Benz C230 Kompressor Drive Cycle below to complete all monitors. Take extreme caution when performing drive cycles on public roadways. Perform the procedure at your own risk.

How to Complete Mercedes Benz C230 Kompressor Drive Cycle

Note: The drive cycle needs to be done two (2) consecutive times. Prior to driving your Mercedes Benz C230 read the drive cycle test instructions carefully and completely to ensure successful drive cycle success. Ensure your Mercedes has at least 1/4 to 3/4 tank of gas. An empty or full gas tank will not allow the EVAP monitor to run. Also begin the drive cycle from a cold start; best achieved by leaving your vehicle sitting overnight. The drive cycle will not run if the check engine light is on or illuminated.

1. Secondary Air Injection Monitor

- From a cold start, start engine and while the vehicle is in Park, accelerate engine speed to 1400 rpm. Ensure A/C system is off and the engine has no load (all lighting, radio, and defroster should be off).

- Allow engine temperature to reach 158°F-200°F. This temperature range should be achieved when your MBZ's temp gauge shows near the middle (normal operating temp).

- Maintain 1400 RPMs for 7 minutes.

- Return engine speed to idle (off throttle) for 6 seconds.

- Turn the ignition OFF.

- Wait ten seconds and repeat this step.

- Continue to Step 2.

2. 02 Sensor Heater Monitor

- Start engine and with transmission in Park and no load applied, increase engine speed to between 2,000 to 2,500 RPM and maintain this RPM for 2 minutes. Keep RPM steady at which ever range you've chosen (between 2,000 and 2,500).

- After 2 minutes, reduce engine speed to idle and run engine with no load applied for 6 minutes. 

- Continue to Step 3.

3. Oxygen Sensor Monitor

- Begin driving. Accelerate to 43 mph (70 km/h) and hold speed for 3 minutes.

- Continue to Step 4.

4. Catalyst Monitor

- Increase speed to between 48-54 mph (80-90 km/h) and continue driving for 3 minutes. 

- Bring the vehicle to a stop and place transmission in Park.

- Idle engine with no load for 3 minutes.

- Continue to Step 5. 

5. EGR Monitor

Place vehicle in Drive and (D position) and accelerate smoothly up to 2000 rpm. Monitoring MPH at this point is not necessary. It is only necessary that you maintain required engine RPMs while your Mercedes is moving. After engine speed reaches 2000 rpms, decelerate smoothly back down to 1100 rpm.

- Stop vehicle. Place transmission in Park. Wait 10 seconds and repeat this step.

- Continue to Step 6.

6. Fuel System EVAP Monitor

- Ensure the fuel tank level is between 1/4 and 3/4 full.

- Ensure engine temperature less than 212°F.

- With the transmission in Park position, start and idle engine for 20 minutes. Ensure there is no load. A/C, radio, lighting, and defroster must be off.

- After 20 minutes, turn engine and ignition OFF.

- Wait 10 seconds and repeat this step.

7. Drive Cycle End

- Perform Steps 1 through 6 again.

If all other emissions systems are functioning properly, completing the drive cycle above should set or make ready (complete) your Mercedes Benz C230 emission monitors. If the emission monitors are still not complete then check for any trouble codes and whether the check engine light is on or not. If faults are found make the appropriate repairs and conduct the drive cycle again.


posted by SmogTips Support

Related Mercedes Benz C230 questions and answers you might find useful:
 

View SmogTips.com in: Desktop / Mobile