Smogtips
CHOOSE YOUR CITY OR ZIPCODE:
Within:
SELECT SMOG CHECK TYPE:  

Join the community and post your question. Use our Ask-A-Tech for free now! ASE experts standing by.

Forum > Failed Smog Test > Question

What is the Drive Cycle for a Hyundai Genesis?

2011 Hyundai Genesis with a new battery. Drove for 4 hours yesterday under different conditions - city street & expressway. Monitors are still not ready. Any suggestions would be appreciated. The smog check place is charging me an additional $20.00 after the initial fee. It’s so frustrating as this is very time consuming. Thank you.
Answer:

How To Make Hyundai Genesis Emission Monitors Ready for the Smog Test

Having replaced the battery on your Hyundai Genesis caused it's emission monitors (also known as readiness flag) to erase. Emission monitors are internal self-tests which the engine control computer (ECU) performs in order to verify specific emissions systems, such as the EGR system, EVAP system, oxygen sensors and Catalyst, are functioning properly. If any one monitor is incomplete, not including the EVAP monitor, your Genesis can not pass the smog test. The EVAP monitor is the only monitor allowed to remain incomplete and the vehicle still pass the smog check because of the difficulty of getting this particular monitor to complete; though the State of California does intend to remove this exemption in the near future. In order to make the monitors ready for the smog check you'll need to drive your Genesis through what is known as a Drive Cycle.

Usually driving 200-300 miles over the course of a few days and in both city and highway traffic conditions is enough to get the drive cycle complete. Due to individual vehicle owner driving patterns however, sometimes the criteria required to get a particular monitor to initiate and/or become ready is not met. In such instances, it is required that a specific drive cycle pattern which is designed for the Hyundai Genesis, be followed.

What is the drive cycle like to get OBD-II monitors ready?

Notice: Take extra caution when performing the drive cycle on public roadways. This particular drive cycle is very complex and requires many stops, starts and slow downs. It is best performed on a dynamometer. Perform the drive cycle at your own risk. If you feel you may be unable to perform the drive cycle below safely, please seek assistance from a reputable smog check repair station or Hyundai dealership. A smog repair certified center will be able to perform the drive cycle on a dynamometer, eliminating the need to drive your car on streets and freeways.

Preconditions: (Make sure you have between 1/4 and 3/4 fuel in the gas tank. The EVAP test will not run while your Hyundai Genesis has a full tank of gas or the gas tank is near empty). Ensure there are no pending or active trouble codes and that the check engine light is not on. Begin the drive cycle from a cold-start; having allowed your vehicle to sit overnight. Note, the secondary air injection monitor will require a cold-start in order to initiate.

    A. Start the engine and idle for 5 minutes in Park (P) or Neutral.

    B. Drive the vehicle at 50 mph for 8 minutes. Ensure to increase speed to 50 mph within 15 seconds.

    C. Stop the vehicle and allow the engine to idle for 15 minutes in Park (P) or neutral. Ensure to decrease speed from 50 mph to idle within 15 seconds.

    D. Drive the vehicle at 55 mph for 1 minute. Ensure to increase speed to 55 mph within 15 seconds.

    E. Stop the vehicle and allow the engine to idle for 1 minutes in Drive (D). Ensure to decrease speed from 50 mph to idle within 15 seconds.

    F. Repeat steps D and E 1 time.

    G. Drive the vehicle at 40 mph for 1 minute. Ensure to increase speed to 55 mph within 15 seconds.

    H. Increase speed to 55 mph and hold steady for 5 seconds.

    I. Decrease speed to 40 mph and hold ready for 1 minute.

    J. Repeat steps H and I 5 times.

    K. During the last time your perform step I, rather than decreasing speed to 40 mph, come to a complete stop.

    L. Allow vehicle to idle for 1 minute in Drive (D).

    M. Drive cycle complete.

If readiness status of all monitors do not switch to "complete" ensure preconditions are met, turn the ignition switch OFF, then repeat steps "A" through "M". Completing the drive cycle above should set the emission monitors required to pass the smog test. We recommend performing the drive cycle 2 or 3 times before the smog inspection. You may use a scan tool to check which monitors have become ready after each drive cycle.


posted by SmogTips Support

Related Hyundai Genesis questions and answers you might find useful:
 

View SmogTips.com in: Desktop / Mobile