Smogtips
CHOOSE YOUR CITY OR ZIPCODE:
Within:
SELECT SMOG CHECK TYPE:  

Join the community and post your question. Use our Ask-A-Tech for free now! ASE experts standing by.

Forum > Failed Smog Test > Question

Honda Accord EX Failed Smog for High HC

My car is a 1996 Honda Accord EX witha 2.2 LTR V-Tec 4-cylinder (F22B1) engine, and manual transmission. I just got a smog check and it failed. The reason for failing was high hydrocarbons HC at idle My Honda measured 133ppm, and the max allowed was 100 ppm. At 2500 RPM the hydrocarbon levels are fine.

The smog technician was very vague and I found it very hard to trust anything he was telling me. They also charged me $58.00 even though the car failed. The results of the smog test showed as "passed" for everything except the high ppm of hydrocarbons at idle. My idle speed during the test was 697 RPM. The car has 141,000 miles on it. I am on a budget and need to sell this car, so I need to fix this problem for as cheap as possible so I can get it sold. Any assistance that can help me get this smog check done would be greatly appreciated.


Answer:

We'll need to look into how well your Honda Accord did on the CO emissions results also; in order to determine why it produced high HC. HC is basically raw fuel (gasoline). High HC means raw fuel is leaving your Accord's tailpipe when it should be burned in the engine.

It is important to know if your Honda Accord is in proper fuel control. Air/fuel mixture must be 14.7:1 in order for fuel to burn efficiently. By looking at the CO emissions which your car produced during the smog test we can ascertain approximately where the fault is that's causing the high HC failure.

If CO emissions where also high during the smog test (but not failing), it is very possible that your Accord is producing high HC due to a rich fuel mixture. If CO is low, then the opposite applies; the air/fuel mixture might be too lean.

We have to recommend you have a smog check repair center conduct a Fuel Feedback Test. This test will ensure your Honda Accord is in proper fuel control, and that air/fuel ratio is as close to 14.7:1 as possible. During the feedback test, a smog technician will check all emission components which are responsible for sensing air intake, oxygen levels in the exhaust, and fuel delivery, as well as whether your Honda's ECU (engine control unit) is receiving and responding to sensor data properly.

For high HC faults not related to fuel control, the most typical faults have to do with improper spark delivery caused by a defective or damaged ignition system components. We are referring to your Honda Accord's spark ignition system; not to be confused with the key ignition system.

As mentioned above, while diagnosing high HC faults it is important to know how much CO the vehicle produced during the smog check as well. A byproduct of incomplete combustion is CO (partially burned fuel). High CO along with high HC indicates a rich mixture problem, while low CO and high HC indicates a misfire condition due to an inadequate amount of fuel entering the combustion chamber. In both scenarios, whether high or low CO was produced, a byproduct of the inefficient combustion will be high HC.

Some Common HC Faults Include:

Vacuum Leaks - Ensure your Honda Accord is not suffering from any vacuum leaks. During idle, intake manifold vacuum is at its highest. Any vacuum leak (after the throttle plate) will cause a lean mixture and increase HC emissions. Once the engine is off idle, HC will return to normal because the fuel injection system will present more fuel to the combustion chambers, neutralizing the vacuum leak. So, checking for vacuum leaks is usually first step.

Ignition and Spark - Once a quick visual inspection has been conducted for disconnected, brittle, or broken vacuum hoses, move on to inspecting the ignition system wiring. Spark plugs and spark plug wires should not show wear, be brittle or cracked. The spark plugs should not appear fouled (heavy carbon build-up) or ashed (whitish appears due to high heat). The distributor cap and rotor must also be inspected for defect or damage.

MAP (Manifold Absolute Pressure) Sensor - The MAP sensor should be checked for proper operation as well. The MAP (manifold absolute pressure) sensor is responsible for letting your Honda Accord's ECU know how much intake vacuum exists. This simple and inexpensive sensor is crucial for proper air/fuel mixture ratio at both idle and off-idle conditions.

How to Test Honda Accord MAP Sensor - You may test the MAP sensor using a voltmeter set to measure voltage. You should see an increase in voltage as RPM increase (intake vacuum decreases). At idle you should see between to 1 to 1.5 volts. Off idle, voltage should start increasing to a maximum of 5.0 volts.

When looking the MAP sensor you will notice the letters V, G, and O, stamped inside the connector well. The MAP sensor signal measurement should be taken from letter O of the three wire connector. You must leave the MAP sensor connected during this test, and back probe the connector. If you have a hand vacuum pump, you may use it to apply vacuum to the sensor, as opposed to running the engine. Disconnect the vacuum line leading from the intake manifold to the sensor and attach your hand vacuum pumps vacuum line instead. Turn your Honda's ignition on, do not start the engine, and conduct the MAP sensor test. If no voltage exists, either at no vacuum or 20in HG vacuum, inspect the other two wires for power (5 volts) and ground. The wire indicated by the letter V should have constant 5 volts while ignition is on. The wire indicated by letter G should be a good ground.


posted by SmogTips Support

 

View SmogTips.com in: Desktop / Mobile