Smogtips
CHOOSE YOUR CITY OR ZIPCODE:
Within:
SELECT SMOG CHECK TYPE:  

Join the community and post your question. Use our Ask-A-Tech for free now! ASE experts standing by.

Forum > Smog Check Repair > Question

2003 Ford Focus ZX5 Drive Cycle

How do I complete a full drive cycle for a 2003 Ford Focus ZX5? I appreciate the help.


Answer:

It is recommended to drive at least 200 miles over the course of a week in order to hit all the specific sections of a complete Ford Focus ZX5 Drive Cycle. Take extra caution when performing the drive cycle on city streets and highways as there are many stops, slow downs, and speed ups. Usually driving in normal traffic on both city streets and highways, over the course of a week completes the drive cycle.

Ford Focus ZX5 Drive Cycle

The following procedure is directly from Ford and designed to complete the OBDII monitors required to get your Ford Focus to pass the OBDII Monitors portion of the smog check, also known of the I/M readiness test. You may use a scan tool in order to monitor the status of the emission monitors as your Ford Focus is being driven.

Drive Cycle Recommendations:

1.Emission monitors (readiness flags) will complete quicker when using a "steady foot" driving style during cruise or acceleration modes. Operating the gas pedal in a "smooth" manner will minimize the time required for monitor completion.

2. Fuel tank level should be between 1/2 and 3/4 fill during the drive cycle in order to allow the EVAP monitor to run. 

3.The Evaporative Monitor can only operate during the first 30 minutes of engine operation. During the EVAP portion of the drive cycle, drive in a smooth fashion to minimize "fuel slosh". 

Drive Cycle Preparation - 1. If using a scan tool, go ahead and connect it now. Turn key on with the engine off. Cycle key off, then on. Select the appropriate vehicle make and model on your scan tool. Start your Ford Focus WITHOUT returning to Key Off. Idle the vehicle for 15 seconds, and then drive at 40 MPH until engine coolant temperature is at least 170°F, which is normal engine operating temperature. 10 to 15 minutes of drive will achieve this.

HEGO Monitor - 5. Cruise at 40 MPH for up to 4 minutes.

EVAP Monitor - 6. Cruise at 45 to 65 MPH for 10 minutes (avoid sharp turns and hills).

Catalyst Monitor - 7. Next, drive your Ford Focus in stop and go traffic conditions. Include five different constant cruise speeds, ranging from 25 to 45 MPH over a 10 minute period.

EGR Monitor - 8. From a stop, accelerate to 45 MPH at 1/2 to 3/4 throttle. Repeat this pattern 3 times.

SEC AIR/CCM (Engine) - 9. Bring your Ford Focus to a stop. Idle with transmission in drive (neutral for M/T) for 2 minutes.

CCM (Trans) - 10. If your Ford has a manual transmission, go ahead and accelerate from 0 to 50 MPH, continue to step 11. For Automatic Transmissions, start from a stop and in overdrive, then moderately accelerate to 50 MPH and cruise for at least 15 seconds. Stop the vehicle and repeat without overdrive to 40 MPH cruising for at least 30 seconds. While at 40 MPH, activate overdrive and accelerate to 50 MPH and cruise for at least 15 seconds. Stop for at least 20 seconds and repeat step 10 five times.

Misfire & Fuel Monitors - 11. From a stop, accelerate to 65 MPH. Decelerate at closed throttle until 40 MPH (no brakes). Repeat this 3 times.

Readiness Check - 12. If using a scan tool, go ahead and access the ON-Board System Readiness (OBDII monitor status) function on the scan tool. Determine whether all emission monitors have completed.

Evap Monitor "Bypass" - 13. Park vehicle for a minimum of 8 hours. Repeat steps 2 through 12.


posted by SmogTips Support

 

View SmogTips.com in: Desktop / Mobile